All Ads

We have 107 adverts and 22 completed so far in October 2020
82 For sale adverts and of these 20 have sold.
21 Wanted adverts and of these 2 found what they needed.
4 Information adverts and no Thank you posts.

Last approved: Tuesday 27th October 2020 at 16:42
Please note that this the date that we last checked the adverts and not the date of the latest adverts, resubmitted adverts could have a date newer than this date as they don't need checking

Details:
Up for offer is an upgraded Raise3D N2 Dual Extractor with filaments. The printer has a new BondTech Dual Extruder from 3DGBRIRE that has been installed and setup with new firmware from Raise3D site. The Filament Run-Out Sensor has been installed and configured to allow the reel to be changed after running out. They is also a N Series Webcam to monitor the print out from the splicer software to check on the job without having to leave your seat, you can do time shoots too.

The printer comes with a aluminium frame with ABS, acrylic, and polycarbonate casing and is packed in a polyurethane protection. Making a print is very simple with the 7" full-colour touchscreen to select the file and allows to restart the print in case of power loss. The screen is able to control the printer without a computer connected but also allow network and wireless options to send the files directly from the software. The Raise3D is able to take a STL file and position, rotate, scale. With multiple parts you can shorten the time taken to print and with the splicer you can add the supports need for complex shapes. When you have finished the model you can change the splicer settings to control so many of the configuration and save them to allow quick use again on the next job.

The device has been looked after and only done about 50 hours of work making prototype parts. They are a Yellow and Red used reel from Raise3D. There is a glue stick for making a printing area for PLA on the glass platform.
This allows you to use a smaller 10 meter filament and even lets you use a different colour. Changing the filament is quick and simple. With many types of colours in PLA, ABS, PETG, Nylon, Carbon Fiber, TPU/TPE (Flexibles), and Metal Composites (with the upgrade to a wear resistant nozzle). The hotends can handle to 300°C and bed up to 100°C. With a 12" x 12" x 12" (305mm x 305mm x 305mm) build space for printing bigger jobs and the Dual head allows for 2 colours or a complex PLA/HIPS dissolvable support.

Machine Specs:
X/Y/Z travel: 12"/305mm
Accuracy: XY-axes: 0.0125 mm, Z-axis: 0.00125 mm
Layer Resolution: 0.01~0.25 mm
Nozzle Size: 0.4mm (other sizes can be fitted)
Filament Size: 1.75mm
Print Technology: FFF
Nozzle Temperature: 150-300ºC
Bed Temperature: 30-100ºC
Printing Surface: Buildtak

Details:
Britool na760c socket set 62 piece whitworth -af -metric in manufacturers pristine condition in original carton

Details:
Set of 3 hard jaws external hold, new but stained these fit 250mm pratt/burnard,
Imp measurements as follows,,

Width of jaws. 1"
Width of grove,. ⁷/₁₆. . 437
Depth of groove. ¹³/₆₄. , 203
Depth of scroll teeth. ¹³/₆₄ . 203
Width between scroll teeth ¹¹/₆₄. 171
Width of scoll teeth, ⁵/₃₂, . 156

Jaws are new, never been used no dings and all have matching number.

£40.00. Plus post uk main ONO

Phone 01255 433583 and leave a message and i will get back to you. Gerry

Details:
Yupiteru MVT-7100 Scanning Multiband Receiver in perfect working order and in very good condition, complete with:

Case (Regretably the window split when last fitted).
Original telescopic aerial.
Flexible aerial,
Wrist strap.
Belt clip.
Battery charger.
Original unused earpiece.
Set of 2700ma rechargeable batteries.
Owners manual.
Downloaded extended manual.
The UK Scanning Directory, 9th edition.

I no longer use this receiver so its time for it to find a new home.

Courier cost would be £8.00 if required, or post at cost.

Details:
Large Surface Plate / Fabrication Plate
Heavy Ribbed Cast Iron Surface Plate
44 inches x 62 inches (1580mm x 1130mm)
Used but in very good condition
Collection from West London or delivery can be discussed.

Details:
A couple of 1949 issues of The Model Engineer Magazine, and one 1954 issue.
Some interesting articles and adverts

---

Yours for free - just £1.50 postage.

Details:
I have at least 50 of these for sale. Price is for one but happy to accept offers for any quantity. The dimensions are 5.5 inches long, thread 8mm by 1mm, square at end is 6 x 6 mm, unthreaded portion is 6mm diameter by 32mm. Postage for one is free but will be charged at cost for larger quantities. Please contact me with any questions and offers. Thanks!

Details:
Motor pulley with ¹/₂ inch mounting hole. Takes 4mm belting. Three steps are 110mm, 84mm and 74mm

Details:
Very good condition footed electric motor. 230v 50 cycle AC, 1.6 Amp, 0.18 KW (1/4 HP). Output shaft is 11mm in diameter with woodruff key slot. Foot is 12cmm by 10cm. Weighs 5.2 Kg unpacked.

Details:
Clare ⁵/₁₆" X 18% cobalt 4 flute end mills (E4004) qty 5
suits clare latch collet system
all in excellent condition (look unused)
free postage.

Details:
Table is 10" dia, its very heavy and probably seen some use. The thin swarf cover on the underneath is missing and the table could do with a light skim. I made 6 T nuts for it. Its a bit too big and heavy for my smallish wokshop.

Details:
I have decided to part with my old Carroll lathe. It is a veteran and historic machine I can't bear to scrap it, but I do not have time to give it the care and attention it deserves. So....
15" AV Carroll lathe (USA) dated 1910, so pre-WW1. It is complete, but originally used overhead line shafting as the drive. It will require a drive added to the machine unless you have a Dibnah-esque steam plant waiting. I can likely fine a suitable motor 3~ or 1~ to your choice.
Basic spec 15"+ dia, 36"-ish between ctrs, back-gear, screw cutting. all up weight around 1 ton, but it breaks down into staggerable lumps apart from the bed. But it does have lovely legs!

There is inevitably some bed wear, but overall it was in regular use when I acquired the machine (35 years ago!) and I have used it very occasionally since. It has been laid-up dismantled into large lumps for the last 10 yrs.
There is a non-original steady, a couple of 3-jaw chucks, a 4-jaw chuck, a good few tools, centres etc, some BIG drills and whatever else I can find to bung in with it.

Note: a couple of the photos show a car gearbox in the drive, this is NOT included (it prooved to be more historically significant than the lathe!). Obviously gas bottles etc in photos also are not included either, it's just the lathe and it's associated tooling and accessories

Details:
Foot mounted motor, GEC ¹/₃ HP, 4 Pole/1440RPM, 240V repulsion start (no capacitor.) Suit most small home lathes, mills & drills etc.

Collection from Ashford or Folkestone, Kent preferred, courier at cost guess £10

Details:
An 18" x 6" magnetic table, english made, in excellent condition.

Details:
Opportunity to acquire all the Copper Boiler parts and a great deal of the castings for a 2 inch scale Burrell traction engine. Although the Copper for the Boiler appears to be all there, it is only a number of the castings needed to complete the engine, but a very good start.

It could be that these parts come from M J Engineers, as they seem to match the pictures and sizes for their 2 inch Burrell. From the price list the castings alone add up to over £400. With the Copper boiler parts which are all flanged the total value is probably over £750.

These could be shipped by courier but a quote would need to be obtained, with insurance probably £25.00

Details:
Large lathe turning steady, looks to be fixed type could be made to move. Probably a Warco Manufacture.

Details:
Large swivel based machine vice for drill or mill 4 inch jaws. In good condition.
Unfortunately no handle the square tightening fitting is 21mm square. Could be shipped by courier but will need to get a quote, probably in the order of £15.00

Details:
This motor will run forwards and backwards and has a 12mm diameter output shaft. Suitable for a battery Loco.

Details:
Simplex 5 inch gauge steam locomotive boiler feed pump casting new in I think Bronze.

Details:
The motors are geared down with a ratio of 9.7:1 and have a 9 tooth sprocket fitted to the output shaft. The 410-9T sprocket is the right size for bicycle chain. The motors will run forwards and backwards. Ideal for battery Locos.

I have four of these motors for sale. £20 discount for all four.

Details:
A long handled coal shovel,
This item has had use and is in fair condition.
18 inches long
The handle is cranked over to about 15 degrees to the shovel.
It looks like it was made that way.

I can post or you can collect from North Notts.

Details:
I am still clearing out a relatives workshop and these have surfaced.
Made from 1.5mm steel, Folded with riveted joints.
Surface rush all over but they do have a bit of age to them.
Blue one is 11 inches long.
Red one 12 inches long.
Selling as one lot.

I can post or you can collect from North Notts.

Details:
A while back, I was fortunate to acquire the remains of a treadle lathe advertised on this site. I'm making it into an elementary wood lathe to turn some handles. I had intended to use the lathe cross slide and remove the top slide to put the chisel rest on. On closer inspection, the two are in quite good condition for their age and in reality, it would be just as easy to fabricate a complete chisel rest. Therefore, the assembly is available to anyone who can use it. I've no idea of the make but the centre height of the lathe is about 4¹/₂".
I also do not need the old treadle base (the only part of the mechanism that came with it) so this is also available to anyone who can make use of it. It is 31³/₄" between the faces of the pivots and 24" front to back. Pivot bolts are included.
If either or both of these are any use and you can collect them then please shout. They are both free of charge. When I obtained the remains originally, I made a donation to the British Heart Foundation so if you would like to do similarly, it would be much appreciated.

Details:
A heavy duty machine vice with 6" wide jaws and a useful 6¹/₄" opening. Good working order

Collection welcome or can post.

Details:
This is a Black and Decker Woodworking Lathe. In good used condition. With it's original box. The bed is a total 24 inches long. It looks like it would produce work up to 12 inches long. It has a faceplate and 2 other small associated parts (Not shown in the pics)
I don't think this has seen any real use but has signes of paint flaking in some places (Mostly around the bed screw holes.)

I'm not sure what its worth.
So does £8 + p+p
If you think the price is outrageous make me an offer.
I would just like it to find a new home.

Collection would be ok from North Notts.

Details:
Antique watchmakers screwhead polishing tool, late 19th/early 20th cent. Three runners for various size screws (one with some old corrosion, see photo).
Useful tool for working on small parts. Postage is 2nd class, unless requested.

Details:
Multifix-Suisse AA toolpost. Unused old stock genuine multifix toolpost by Mivesa. Comes complete with original locking lever. Postage is Royal Mail second class, unless requested.

Details:
4 way Superseal connectors ( x 2 of).
Flexible conduit (split type), 10mm inside dia., 5 metre length.
The lot for £8 inc UK postage.

Details:
Two truck ni10-k20-az3x proximity switches 10mm sensing distance 20-250 volts ac n/o

Details:
Three Micro switches in good working condition. Two are rated at 15Amps 480Volts, press to activate, One is rated at 10 Amps 480 Volts and has a rotary actuation.
£5 Each or all three for £10.
Collect from Staines, or add postage costs.

Details:
Practical Mechanics
13 various issues from January 1949 through to March 1959.
Fascinating reading of amateur mechanics, workshop tooling and new developments such gas turbine cars and believe it or not mobile phones! Etc. at a time of exciting new ideas in various fields.
All in good condition and complete with adverts and covers
Collected from West London or can post at cost.

Details:
This pair of power factor correction units were removed last year to make way for an uprated automatic staged unit.
They are now surplus to requirements.

Two separate units internally wired together, (I prefer to sell them as 1 lot.)
Rated at 35 Kvar each. (Total 70 Kvar)
3 Phase.

These will help to reduce the reactive charge on your electric bill.

Collection from North Nottinghamshire. NG21.
Or I can send them by carrier. at a cost of £20.

These were in good working order when removed.

Details:
English House Clocks 1600 – 1850
By Anthony Bird 1973
Hard Covers with Dust Jacket. 313 pages. Profusely Illustrated.
Excellent as new Condition. £15

Grandfather Clocks and their Cases
By Brian Loomes 1985
Hard Covers with Dust Jacket. 352 pages. Profusely Illustrated.
Excellent as new Condition. £30

Collected from West London or can post at cost

Details:
Selection of Leigh Dovetail Jig Books and Manuals:
Leigh D3 Dovetail Jig User Guide,
Leigh F1 Finger Joint Template User Guide,
Leigh Dovetail Jig Model D-1258R Owners Manual,
and Sales Leaflet
Good condition
Uk only.
Postage is for mainland, highlands and islands may be more.
Any questions just ask

Details:
Meca universal dividing head in beautiful condition.200mm swing with banjo and seven change wheels tail stock catch plates driving arbor
support jacks

Details:
A Very Nice Shardlow Micrometer in Wooden Box That is no longer Wanted and needs a New Home.

Details:
Air Compressor
240 volt 1 Phase 3hp Motor
7cfm Cast Iron Pump
150 Litre Air Receiver
Mains Presure On / Off Switch
Pressure Guage
Pressure Release Safety Valve

Details:
Long handled sand scoop for metal detecting on beaches - dig without bending down. Re-advertised due to no contact. Lightweight custom that was my dads.

Also included his digging tool with scabbard for normal field detecting, it turned up while i was waiting so have included it. Think its called a side digger!

£45 the lot collected from near Colchester or UK mainland courier £15 because of size - if i can get the postage down will refund the difference.

Details:
A vintage tilt and swivel machine vice with setting in 3-axis. This has 3" wide jaws. The moving jaw has some play and witness marks, but the main axis movements are very firm and smooth. Please see photos for condition.

Details:
Sixteen used machine and hand reamers, imperial largeish sizes ie ³/₄" etc. £20 plus postage at cost.
Five horizontal milling cutters 1" bore £5 postage at cost.
3mm pre-fluxed brazing rods plus ¹/₄ tub Tenacity 4a fludx £25 plus postage.
Five 1 Kg bars Muliticore 63/37 solder £4 each plus postage. Finally selection of switches and indicator lights f.o.c plus postage. Phew!